The Additive Manufacturer Green Trade Association (AMGTA), a global advocacy group focused on promoting sustainable additive manufacturing industry practices, has released the preliminary results of a research project titled ‘Specific Energy of Metal AM Feedstock: A Comparison.’ The study, commissioned by the AMGTA and conducted by Syntec Associates, a research consultancy, in partnership with Divergent Technologies, a complete modular digital factory for complex structures, evaluated three key metal AM feedstock processing approaches – gas atomization, mechanical milling (specifically ball milling), and wire drawing – to determine specific energy requirements for producing metal AM feedstock materials.
The research findings highlighted that, from an energy perspective, helium gas atomization is the most sustainable method used for gas atomization for metallic powder production of commonly used alloys – followed by argon, and then nitrogen. Specific energy consumption for atomization also critically depends on process parameters and alloy chemistry. Additionally, the research showed that mechanical milling, when appropriate for use in powder production in AM, exhibits a significant reduction in specific energy consumption when compared to gas atomization.
“When preparing life cycle assessments on industrial rate processing of our alloys, I found wide variation in the literature on AM process and powder atomization energy consumption,” said Michael Kenworthy, Chief Technology Officer at Divergent Technologies and AMGTA Board Director. “This research established a transparent set of process assumptions and models from which to understand the key process levers and evaluate system trade studies that inform future sustainability enhancements.”
Helium gas atomization is best for powder atomization: The research indicates that, from an energy perspective, helium gas atomization stands out as the most sustainable gas atomization method – showing a significant reduction in specific energy consumption compared to argon and nitrogen for commonly used alloys.
Argon-atomized powder is better than nitrogen: For those seeking an alternative to helium, the argon-atomized powder is revealed to be a notable option – saving energy when compared to nitrogen-atomized powder.
Mechanical milling outperforms gas atomization: Mechanical milling, particularly ball milling, demonstrates a significant reduction in specific energy consumption compared to gas atomization for metal AM powder production.
Industry guidance for sustainable choices: This research highlights the importance of selecting manufacturing methods with the lowest specific energy consumption per kilogram to enhance overall sustainability when producing feedstock materials used in AM.
“A primary goal of the AMGTA is to educate the consumer on the most sustainable methods of production within the additive supply chain. This important piece of research provides guidance on which methods of gas atomization require the least amount of specific energy per kilogram,” said Brian R. Neff, Board Chair of AMGTA. “At the same time, it indicates to the market that mechanical production methods of powder feedstock, such as ball milling, are themselves an order of magnitude better than gas atomization from an energy perspective.”
Gas atomization, deemed a promising technology for producing stock powders for AM, was a focal point of the study. The research revealed that gas atomization using helium as the atomization gas resulted in the least total specific energy consumption compared to argon (13% better on average) and nitrogen (28% better on average). Additionally, argon-atomized powder was found to reduce energy requirements by 12% when compared to nitrogen-atomized powder for the alloys studied (SS316L, Al5083, and IN718).
The study also highlights the efficiency of mechanical powder production, particularly ball milling, which showed approximately a 90% improvement in specific energy consumption compared to gas atomization for the range of process conditions studied. Further research is recommended to determine the applied impact within specific product categories of using helium-atomized powder and/or ball-milled powder.
“This research aligns with the AMGTA commitment to better understand sustainable manufacturing practices leveraging additive technologies,” said Sherri Monroe, the Executive Director of AMGTA. “These findings highlight key considerations for manufacturers seeking environmentally friendly feedstock production methods. To advance sustainability in additive manufacturing, research is vital in order to make informed decisions.”
The AMGTA says it expects to publish additional independent research throughout 2024.
746 composites AM companies individually surveyed and studied. Core composites AM market generated over $785 million in 2023. Market expected to grow to $7.8 billion by 2033 at 25.8% CAGR. This new…
Your email address will not be published. Required fields are marked *
I have read and agree to the T&C.
When you visit any web site, it may store or retrieve information on your browser, mostly in the form of cookies. Control your personal Cookie Services here.
Newsletter
Join our 12,000+ Professional community and get weekly AM industry insights straight to your inbox. Our editor-curated newsletter equips executives, engineers, and end-users with crucial updates, helping you stay ahead.